Biqu

Biqu смотреть последние обновления за сегодня на .

The fantastic* BIQU H2 extruder/hot end - (*IF you get a good one)

98614
2548
243
00:16:22
18.06.2021

The BIQU H2 should be a E3D Hemera killer. Smaller and lighter for less money. The only problem is, some of them are lemons. In this guide and test I try out five to get a better picture as to their reliability. The XChange system from printermods.com has just started shipping. THe H2 was a great match with two custom tool plate holes. There are also mounts available below to fit the H2 to a stock machine. The H2 this video started with was originally supplied free of charge by BTT. They also supplied a free replacement. In addition to this, I purchased another with my own money for comparison. All opinions expressed are my own. If you get a working one they are pretty damn good. I you don’t, make sure Bigtreetech supply a replacement. Purchase the H2 from Amazon: 🤍 Purchase the H2 from Aliexpress: 🤍 Purchase the metal heat break from Aliexpress: 🤍 0:00 Introduction Previous video testing BIQU BX prototypes: 🤍 0:45 Specifications and unboxing BTT product page and technical information: 🤍 Previous video on fitting the Hemera to an Ender 3: 🤍 Previous video on fitting the Hemera to a CR-10 Max: 🤍 2:51 Disassembly & comparison with E3D Hemera, Bondtech LGX Bondtech LGX video: 🤍 5:27 Standard mounting options BTT mount downloads: 🤍 Creality CR-10/Ender mount on Thingiverse: 🤍 6:14 XChange update and mounting Previous XChange video: 🤍 Paste extruder printing Nutella: 🤍 XChange Kickstarter update page: 🤍 Printermods XChange GitHub page: 🤍 My printed wire clip and drilling jig: 🤍 8:28 Part cooling solution 5015 fan duct (original): 🤍 5015 fan duct (remix): 🤍 10:00 Firmware and slicer setup BTT product page and technical information: 🤍 My free troubleshooting page (reverse extruder direction if necessary): 🤍 10:45 Calibration My free calibration website (PID autotune, E-steps, flow, retraction tower, etc): 🤍 11:29 Reliability issues 13:22 Reliability testing results 14:38 Print results 15:26 Conclusion: Much more potential! Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: 🤍x3d.com.au Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5] 🤍 Take a look around and if you like what you see, please subscribe. Support me on Patreon: 🤍

Ender 3 V2 vs BIQU B1 head to head review

140916
3274
422
00:16:55
04.09.2020

The Ender 3 was a hit, so which printer is best to succeed it? The Ender 3 V2 and BIQU B1 are both upgraded Ender 3 style 3D printers, which have been put to the test in this review. Personally, I prefer the appearance of the Ender 3 V2. I prefer the mainboard and removable bed of the B1, however. Both of these printers are closely matched. Both of these printers were supplied free of charge for review by the manufacturers. All opinions expressed are my own. Purchase the Ender 3 V2: 🤍 Creality Ender 3 V2 (Amazon): 🤍 Purchase the BIQI B1: 🤍 Purchase the original Ender 3: 🤍 Previous Ender 3 V2 vs BIQU B1 initial impressions video: 🤍 My Ender 3 playlist: 🤍 SunShine print in place engine video: 🤍 Models featured in this video: SunShine Print in place engine STL: 🤍 Twist gear vase: 🤍 Business card embosser: 🤍 Reversible Flexy Bracelet: 🤍 Spring clip - ABS version: 🤍 Phrozen Sonic Mini vat base: 🤍 Part cooling torture test: 🤍 Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: 🤍x3d.com.au Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5] 🤍 Take a look around and if you like what you see, please subscribe. Support me on Patreon: 🤍

BIQU BX 3D printer for advanced users: Pros and Cons, Raspberry Pi, Smart filament sensor setup

16314
712
88
00:14:33
07.06.2022

00:00 Intro 02:29 Unboxing, assemble, setup 04:50 Test Print 1: PLA 3D Benchy 05:23 Setup Cura 05:55 Test Print 2: PLA Calibration Cube 06:38 Test Print 3: PLA 3D printer testing model, compared with Ender-3 S1 Pro 07:12 Test Print 4: PLA Dual color Fidget spinnner 07:34 Test Print 5: PETG London Bus 08:18 Test Print 6: ABS shelf bracket (without using glue stick) 09:05 Test Print 7: ABS shelf bracket (using glue stick) 09:16 Test Print 8: TPU flexable iPhone case 09:39 Test Print 9: Nylon nut 09:56 Raspiberry Pi setup & Cura plug-in 11:12 Install Filament sensor 11:44 Pros and Cons Welcome back to Aurora Tech Channel. Today, I will review a 3D printer from BIQU, or better known as Big Tree Tech. If you like doing DIY upgrades, you may already have their motherboard or touch screen installed on your printers. I am going to review their flagship 3D printer, the BIQU BX. This printer has been around for 18 months somewhere between the end of 2020 and the beginning of 2021. It has some of the best hardware specifications among the mid-range printers, and some people even call it the 3D printer for Enthusiasts. Let’s take a look at the hardware. It has a 7” touch screen, so it’s almost like a tablet on the right side of the machine. It supports a USB drive, a standard SD card, and a Micro SD card. There is a Raspberry PI connector at the back of the touch screen, so you connect the Raspberry Pi directly to the printer and use the same 7” touch screen. So, it supports 3 different modes: the classic Marlin mode, the touch screen mode, and the Raspberry Pi interface like the OctoBTT or OctoDash. It came with the H2 extruder, which is one of the best extruders you can get for under $100, and the short filament path between the extruder gears and the nozzle. It has a dual steel gear with a 7 to 1 gear ratio, and even a pancake stepper motor can generate enough force to push the filament, as it’s compact and the total weight is just 203 grams. Generally, the processor of most 32-bit 3D printer motherboards is a Cortex M3 that runs at 72Mhz, but this printer came with a Cortex M7 processor that runs at 400Mhz. The stepper motors are 0.9 degrees compared to the 1.8 degree ones used on most 3D printers. There are 5 TMC2226 silent stepper drivers, and the dual Z-axis are controlled by 2 independent stepper drivers that can use the firmware to align the level of the gantry. It also came with an inductive auto bed leveling sensor, and there are belt tensioners on both the X and Y-axis. The hardware specifications of this printer seem nice to me. I would like to thank BigTreeTech for sending me this machine to review, and with that, let’s get started. Affiliate links: Buy BIQU BX from Official website ($521.56) 🤍ent/collections/3d-printer/products/biqu-bx-3d-printer-fdm-3d-printer-with-32-bit-400mhz-motherboard-integrated-octoprint?variant=39442157305954 BIQU BX Lowest price as today 6/6/2022 ($497): Buy from Amazon: 🤍 BigTreeTech smart filament sensor: 🤍 Smart filament sensor installation: 🤍 Smart filament sensor mount for direct extruder: 🤍 BigTreeTech OctoBTT image for OctoPrint 🤍 Creality Refurbished Printers (SAVE UP TO 50%): 🤍 Used Ender-3* ($79): 🤍 * Maybe in bad condition, but if you know how to fix some common issues of a 3D printer and have spare parts to replace by yourself, that could be an amazing deal: Follow us on Twitter 🤍aurora_lung

The BIQU BX is an innovative 3D Printer, and a little strange.

174971
4330
512
00:14:04
22.10.2020

In this video we're checking out a preproduction BIQU BX 3D Printer from Bigtreetech - currently on kickstarter. This 3D Printer has some really interesting features and, despite encountering some preproduction glitches, I think it's worthy of your attention. UPDATE: Some really good responses by BIQU to issues raised in this video , confirming the firmware bug and plans for the other small areas of concern - 🤍 Teaching Tech's video on the BIQU BX - 🤍 Link to the Kickstarter campaign (back at your own risk) - 🤍 Models tested: 3DBenchy - thingiverse.com/thing:763622 Clearance Gauge - 🤍 Fillenium Malcon (definitely from star trek) - 🤍 Stringing Test - 🤍 Support Maker's Muse on Patreon 🤍 50 3D Printing Tips and Tricks - 🤍 3D Printing Essentials - 🤍

The Biqu B1 Sub $300 3d Printer Comes Packed With Upgrades!

86389
2232
375
00:21:37
23.01.2021

Love the channel? Consider supporting me on Patreon: 🤍 In this video we take a look at the Biqu B1 3d printer. This is a low cost 3d printer from Biqu or BigTreeTech that comes with some very impressive hardware for the price. In this video we take a look at the specs, print quality, and my experience using this machine over the past few weeks. Find out more or purchase yours here(AFF): 🤍 Video on printing with HIPS: 🤍 Models used in video: Nintendo Switch Joy-Con Wheel Pro: 🤍 Stitch Disney- easy print: 🤍 Cthulhu Idol Dice Tower: 🤍 (´∀`)♡ As an Amazon Associate I earn from qualifying purchases: Buy now on Amazon: 🤍 Subscribe To My 3d Printing Blog! : 🤍 Lets Get Social! Facebook: 🤍 Twitter: 🤍 Instagram: 🤍 Twitch: 🤍 Music provided by Argofox: NEREUS - Lotus 🤍 Time Stamps: 0:00 - Intro 3:13 - Printer Specs 6:08 - A Look At The Electronics 7:31 - Setup and Assembly 9:06 - Printing 16:44 - Conclusion 20:13 - Outro

BIQU Hurakan 3D Printer - Is It The Amazing Klipper 3D Printer You're Been Waiting For?

38747
727
64
00:17:03
17.10.2022

In this review, we take a look at the Biqu Hurakan 3D Printer, which is a fantastic option if you're looking for a high-quality 3D printer. We take a look at klipper, the input shaper, and the overall performance of the machine. So! if you're looking for a quality 3D printer that's affordable! This video is independently sponsored by 🤍 head over there to discover the best in the business when it comes to production of PCB design, fabrication and ideas! Biqu reached out to many creators about reviewing this printer! Mine arrived while over in the USA at ERRF, so as soon as I got back I got to work! I was really keen to see what klipper had to offer inside this machine. Fancy this on a pre order? 🤍ent/collections/3d-printer/products/biqu-hurakan-diy-3d-printer?variant=40089640960098 Want to know more about Klipper? 🤍 What on earth is input shaping? 🤍 Pressure Advance 🤍 🤍 home of the infinity dragon! Socials: 🤍instagram.com/therealsamprentice 🤍twitter.com/samprentice 🤍youtube.com/therealsamprentice​

#biqu PIXEL L - Resin Drucken mit allen Extras!

718
62
8
00:32:48
02.02.2023

Dieses Review war mein eigener Wunsch, der Drucker faszinierte mich schon seit erscheinen. Er ist wie man im englischen sagen würde "Outstanding". Er kommt voll gepackt mit durchdachten Extras, Funktionen und ist aus hochwertige Materialien gefertigt, welche jeden Cent für diesen rechtfertigen. 00:00 - Willkommen 01:00 - "Auspacken" und Teaser 04:04 - Auf geht's in die Details, viele Details! 14:42 - Das Zubehör 16:20 - Leveln? Hier alles etwas besser! 19:12 - Luftfilter inklusive! 20:15 - Was ist den im Gehäuse? 22:29 - Ich Drucke auch hier mit PEI 25:09 - Los geht's... drucken 27:27 - Fazit und was hat er gedruckt? Erhalten könnt Ihr diesen hier: 🤍ent/collections/3d-printer/products/biqu-pixel-l-9-1-inch-4k-photocuring-lcd-3d-printer?variant=39753757261922 Eine passende PEI könnt Ihr direkt bei 🤍biqu7927 kaufen oder auch bei Amazon, wo ich noch mehr findet, auch für andere Drucker: 🤍 Das Model welches ich gedruckt habe, ist übrigens dieses hier: 🤍 Du willst mich unterstützen? Paypal: 🤍 Patreon: 🤍 Für fragen schreibt mit eine Mail an: frage [at] stone-time [dot] de Oder komm in meinen Discord: 🤍 Ein Dank geht an die großartige Unterstützung von 🤍OsLee540i (🤍 3D Drucker und Zusatzgeräte: :: Voron 0.0, diverse an/umbauten :: - Crydom ED24D3 SSR - 🤍 - SKR Mini E3 - 🤍 - Raspberry PI4 4GB - 🤍 - SanDisk 32GB Karte - 🤍 - E3D Hotend 24V - 🤍 :: Voron Legacy :: :: Sapphire Pro - Klipper + Tochscreen, diverse an/umbauten :: - DSI Display - 🤍 - DSI Verlängerung - 🤍 - USB Verlängerung - 🤍 - Netzwerk Verlängerung - 🤍 - Raspberry PI4 4GB - 🤍 - Netzteil - 🤍 - SanDisk 32GB Karte - 🤍 - Noctua NF-A6x25 - 🤍 - Noctua NF-A4x10 - 🤍 - DCDC StepDown - 🤍 - ruthex M3 Inserts (für die Druckteile) - 🤍 - Jumper Wires - 🤍 :: AnyCubic Photon S - 🤍 :: AnyCubic Wash & Cure 2 - 🤍 :: Creality CR200B - 🤍 Film Equipment: - GoPro Session 5 [ for recording on all 5 zoll Quads ] - 🤍 - GoPro Hero 3+ Black [ for recording on ground ] - 🤍 - GoPro 8 Black [ for recording on ground ] - 🤍 - DJI Osmo Pocket [ for recording on ground ] - 🤍 - Rode Wireless Go [ for recording on ground ] - 🤍 - Rode NT-USB [ for desktop recording ] - 🤍 - Logitech Brio [ for desktop recording ] - 🤍 - Sony Alpha 6100 - 🤍 * Alle Links die ich euch zur Verfügung stelle sind Affiliate-Links. Ihr habt dadurch keine Einschränkungen, helft jedoch mir diesen Kanal zu betreiben. #biqu #pixel #sla #lychee #slicer #fdm #resin #sla #klipper #mainsailos #Voron #SapphirePro #E3D #anycubic #VoronM4 #StoneTime #fpv #fusion #fusion360 #anfänger #tutorial #erklärung #oslee544i #Freestyle #Drone #Meeting #Tiny #Friends #Action #Challenges #Germany #Berlin #Fun #Deutsch #FPV #Tutorial #Newbee #3d #drucker #konstruktion #raspberry #pi #touchscreen #pi3 #noctua #ikea #lack #basic #reihe #discord, #action #betaflight #deutschland #vlogging #fusion360 #fusion360tutorial #autodesk #cad #beginner #grundlagen #grundkurs #modellieren #einstellungen #zeichnen #OsLee540i

BIQU H2 Extruder Review

59040
1205
148
00:12:06
16.01.2021

In today's video, we take a look at the BIQU H2 extruder and hotend combo. Install Raid for Free ✅ IOS: 🤍 ✅ ANDROID: 🤍 ✅ PC: 🤍 and get a special starter pack 💥Available only for the next 30 days! Buy the H2 at these places: Amazon (affiliate): 🤍 AliExpress (affiliate): 🤍 Ebay: 🤍 biqu. equipment: 🤍 Official Website: 🤍 Files Used: Mount and Fan Shroud I designed: 🤍 Fan Shroud I edited: 🤍 Meet the Flexible Video with 3DX Tech: 🤍 Time Stamps: Intro - 00:00 Unboxing and Info - 1:58 Mounting - 4:44 PLA Tests - 5:53 Flexible Tests - 7:26 Final Thoughts - 10:05 Background music by Joakim Karud: 🤍 Follow now for more free giveaways and 3D printing tutorials! Visit 🤍 for products I have used in the past and approve. You can also rep 3D printing and support the channel via my Merch Store: 🤍 Grab the 2020 Edition of my 3D Printing Failures book: 🤍 Purchase at a discount at my Patreon: 🤍

BIQU B1 - 3D Printer - Unbox & Setup

99047
1395
151
00:56:29
04.09.2020

Amazon Links Buy it here: 🤍 Official: 🤍 Recommended: 🤍 BIQU B1 3D Printer TFT35 V3.0 Touch Screen SKR V1.4 32 Bit Dual Operation System DIY I3 3D Printer Technical Specifications: Technology: FDM Print size ( X Y Z ) 235*235*270mm Print Speed: 60-100mm/s Layer Resolution: 0.1-0.3mm Filament Diameter: 1.75mm Nozzle Diameter: 0.4 mm Filament Compatibility: PLA ,ABS, PETG,TPU etc. Chassis Spring Steel Metal Sheet Software Specifications 3D Printing Software: repetier-host, CURA, Simplify3D Supported File Formats: STL,G-Code,AMF,OBJ Operating System: Win/mac/linux Temperature Specifications Extruder Temperature: 260 deg C Heating Bed Temperature: 100 deg C Power Requirements: 100 - 120V / 200 - 240V 50 / 60 HZ Output Voltage - 24V Rated Power - 270W Connectivity (Interface) USB or SD Card or Type C data cable Electronics Specifications Display: BTT TFT35 V3.0 Machine weight: 8 Kg Shipping box weight: 9 Kg Machine Dimensions: 412*492*402 mm Shipping box dimensions: 530 x 410 x 180 mm As an Amazon Associate I earn from qualifying purchases My website: 🤍

O Mundo maravilhoso da impressão 3D! BIQU B1

74
22
4
00:07:14
02.02.2023

E ae gente, tudo de boas? Estou amando minha nova impressora 3D! Ela é uma ótima opção para quem quer começar! Nesse vídeo aprensento a vocês minha BIQU B1! Meu canal de games: 🤍youtube.com/channel/UCd4IhIjWmhNmy4YeWHF37SQ E-mail para contato: contatosacarod🤍gmail.com Me siga no Insta: 🤍rodmpro Me siga no Twitter: 🤍canalsacarod #sacarod #biqub1 #impressao3d #3dprinter

BIQU Micro Probe review with a printer saving tip included.

643
24
28
00:09:53
22.01.2023

Today's video is going over the new BIQU Micro Probe. This is a tiny bed leveling device that is very accurate. Printer Setup: * BIQU Hurakan * BIQU H2 V2s Lite * BIQU Micro Probe * Klipper Firmware

Tutorial:How to install the BIQU H2 Extruder on the BIQU B1 3D Printer

27495
205
61
00:03:39
02.02.2021

Hi everyone, the BIQU H2 extruder has been released. Many of you wonder about the direct extruder that can be installed on your BIQU B1 printer. Here, we make a tutorial so that it can better help you. The BIQU H2 extruder is one of the lightest extruders in the world. It has the following advantages: - Lightweight, Compact and Powerful - A Unique Cooling System - Supports A Wider Range of Filaments - Flexible Mounting Options For DIY - Extreme Smoothness, Less Clogging 🔗Official website: 🤍bigtree-tech.com 🔗Buy the BIQU H2 extruder (official website): 🤍 🔗Buy the BIQU H2 extruder (Amazon): 🤍 🔗Buy the BIQU H2 extruder (biqu.equipment): 🤍 🔗Buy the BIQU H2 extruder (AliExpress): 🤍 🔗Buy the BIQU B1 adapter board (AliExpress): 🤍 🔗Buy the BIQU B1 adapter board (Amazon): 🤍 🔗Buy the BIQU B1 blower fan (AliExpress): 🤍 🔗Buy the BIQU B1 blower fan (Amazon): 🤍 🔗Buy the BIQU B1 3d printer (Amazon):🤍 👉More info can follow our channel: BIQU (FB): 🤍 BIQU (Twitter): 🤍

BIQU B1 SE Plus - BIQU's First Integrated Auto Leveling Printer for 3D Printing Beginners

14366
95
8
00:04:31
18.08.2021

BIQU B1 SE Plus is the first integrated auto-leveling 3d printer launched by BIQU in 2021. Perfect for 3d printing beginners. Features: ✅ Integrated auto-leveling ✅ Large build volume: 310X310X340mm ✅ Modular design, easy assembly ✅ Aluminum Extruder, smooth filament loading ✅ Powerful ARM Cortex-M4 Chip ✅ TMC Silent Driver, noiseless printing ✅ Carborundum Build Surface & Improved Heatbed ✅ Filament Runout Detection, power loss recovery 🛒 Make It Yours: ✨ B1 SE Plus (Official website):🤍 ✨B1 SE Plus (eBay): 🤍 ✨ B1 SE Plus (Amazon): 🤍 ✨Hot bed(Amazon): 🤍 ✨Special Offer Code: ULXV5R3B ✨B1 SE Plus (AliExpress): 🤍 ✨ B1 SE Plus (Shopify): 🤍 👉 Unbox & First Print LIVE: 🤍 🌈More info: Official website: 🤍 BIQU (FB homepage): 🤍 BIGTREETECH (FB homepage): 🤍 BIQU (Twitter): 🤍 BIGTREETECH (Twitter): 🤍

Direct Drive Battle! - Part 4 - The HotRod - Biqu BX

9473
214
96
00:45:48
15.04.2022

This is part 4 of our Direct Drive series! This time, we take a look at what I'm calling the HOTROD! The Biqu BX has so much I had to write it all down. Might be a first. Now, let's see how it prints. - In this video: •Biqu BX• Official site: bit.ly/3KKVWPubit.ly Buy it from IIIDMax USA: 🤍 Amazon: 🤍 •YouSu 2 Color Silk Filament• Amazon: 🤍 •IIIDMAX Filament• Official Site: 🤍 Amazon: 🤍 Car model by SoarPix.com - Timestamps: 0:00 - Demo Reel 0:13 - Intro 3:25 - Unboxing 8:37 - Motherboard Details 10:06 - Assembly 10:42 - In-Depth Look at the Menus 23:24 - Leveling 25:27 - First Prints 28:44 - Initial Impressions 31:00 - CONS 36:18 - PROS 41:49 - Print Quality 43:28 - Final Thoughts 44:49 - Conclusion - Join the 3DPrintSOS Discord Server: 🤍 Become a Patron: 🤍 Buy me a coffee: ​​🤍 - US Links: Aquila Extender Kit: 🤍 (Coupon code for 5% off: 3DPrintSOS) IIIDMax Filament: 🤍 Voxelab Aquila X2: 🤍 (Use coupon code "VOXELABFS" for 5% off your order!) Voxelab Aquila on Amazon: 🤍 (Use coupon code "VOXELABFS" for 5% off your order!) on Official Voxelab Website: 🤍?aff=4 Creality Ender 3 V2: 🤍 Yousu Silk Filament: 🤍 CR Touch: 🤍 BL Touch: 🤍 BL Touch Clone: 🤍 Wire Loom Tape: 🤍 Wire Loom: 🤍 Capricorn PTFE Tubing: 🤍 Hardened Steel MK8 Nozzles: 🤍 .4 and .5mm MK8 Nozzle pack: 🤍 Isopropyl Alcohol: 🤍 Bolts kit: 🤍 T-Nuts: 🤍 - UK Links: BL Touch: 🤍 Wire Loom Tape: 🤍 Wire Loom: 🤍 Voxelab Aquila on Amazon: 🤍 on Official Voxelab Website: 🤍?aff=4 Creality Ender 3 v2: 🤍 Yousu Silk Filaments: 🤍 - CANADA Links: CR Touch: 🤍 BL Touch: 🤍 BL Touch Clone: 🤍 Wire Loom Tape: 🤍 Wire Loom: 🤍 Voxelab Aquila X2: 🤍 Voxelab Aquila on Amazon: 🤍 on Official Voxelab Website: 🤍?aff=4 Creality Ender 3 v2: 🤍 Yousu Silk Filament: 🤍 - NOTE: Some of the links above are Amazon Affiliate Links. They do NOT cost you anything but using them and making a purchase helps the channel a tiny bit. This is one way I can afford to continue to make content for this channel. Thank you for your consideration. :)

BIQU BX - Octoprint compatible 3D printer on Kickstarter

63208
1700
265
00:17:02
16.10.2020

A 3D printer with factory Octoprint integration and a touch screen interface? That’s what Bigtreetech is offering on Kickstarter with the BIQU BX. Should you back it? This video is an honest depiction of my experience testing not one, but two BX machines. BIQU BX Kickstarter: 🤍 OctoBTT GitHub: 🤍 OctoDash GitHub: 🤍 OctoDash is compatible with the BIQU BX. Burn your Octopi image, add your wifi details as normal, edit config.txt with the LCD settings from the bottom of the OctoBTT readme, then follow the OctoDash installation as usual. These printers were provided free of charge by Bigtreetech for the purposes of testing and making this video. All opinions expressed are my own. Clearly, Bigtreetech sends printers like this to content creators to promote their product but I enjoyed the chance to test and give feedback. At times I was quite forthright with constructive criticism, but BTT were receptive as as a result the final product should be improved. Some more thoughts: -The first version was bug ridden and I couldn’t recommend it. -The updated version was a clear step forward with all bugs fixed. I didn’t experience any issues on this version. -Print quality is what you would hope. I will put the printer through some calibration to optimise it. If anything, the part cooling fan is the weak link, however the extruder design and breakout board will make this easy to upgrade if necessary. -OctoBTT looks to be based on OctoDash. Both projects are open source, this is all above board. OctoBTT introduces some new features but is not yet polished. In time it should improve. -OctoDash is quite polished and a great alternative solution. Check the GitHub wiki to see the options and themes available. -Assuming the three issues I noted at the end of the video addressed, this would seem to be a really great printer. This is not a review however, my review process is a lot longer and more exhaustive. -Kickstarter pledges do not guarantee a product, please read here: 🤍 -Watch as many videos about this as possible from other creators to get a broader picture Models featured in this video: Rubber ducky: 🤍 Falcon clamp: 🤍 Baby Yoda: 🤍 Ender 3 webcam mount: 🤍 Ratchet clamp: 🤍 Information from viewer Alan: "I sponsored this on Kickstarter and received my printer early February 2021. I was also intrigued with the HDMI connector for the hot end connections. After a number of successful prints (approx 25) of various benchies and calibration stuff, I attempted my first sizeable print .....about 14 hours. I have the unit in a thermal enclosure to minimize temperature variations. The print failed after 8 hours with thermal runaway messages. After a few tests to try and establish where the fault was, I swapped out the heater and thermistor for replacement ones and tried the print again. It failed again after 9 hours with the same error message. Having seen reviews about the qwerky use of an HDMI connector, I decided to run separate cables from the hot end pcb all the way to the control board. Problem solved!! I have done a number of lengthy prints (18-26 hours) and have had no failures. I can only conclude that the very small contacts and contact area on the HDMI is unsuitable for either the heater circuit or thermistor feedback. I did feed these findings back to BTT tech support for there information." Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: 🤍x3d.com.au Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5] 🤍 Take a look around and if you like what you see, please subscribe. Support me on Patreon: 🤍

BIQU B1 3D Printer Review

35328
723
86
00:13:00
14.08.2020

In today's video, we take a look at the BIQU B1 3D printer by Big Tree Tech, which comes in at under $300. Buy and find out more (not affiliate) Shipped from America: 🤍 Shipped from China: 🤍 Sorry if any prints were hard to see - I need to get a good macro lens. Will be grabbing one ASAP Other items used (affiliate) Capricorn Tubing: 🤍 Polymaker PolyLite PLA: 🤍 Background music by Joakim Karud 🤍 Follow now for more free giveaways and 3D printing tutorials! Visit 🤍 for products I have used in the past and approve. You can also rep 3D printing and support the channel via my Merch Store: 🤍 Grab the 2020 Edition of my 3D Printing Failures book: 🤍 Purchase at a discount at my Patreon: 🤍

Installation tutorial for BIQU B1

28397
303
27
00:27:50
29.07.2020

1. Appearance: The violet color makes its appearance more attractive Independent chassis and 2040 aluminum profiles 2. Motherboard: 32-bit motherboard SKRV1.4 to facilitate DIY 3. Driver: TMC silent drive series 4. Screen: BTT TFT35 V3.0 (1)Marlin mode & Touch screen mode (2)15 languages (3)Modes can be switched as needed (4)Model preview (5)Real-time monitoring data (temperature, progress, height) (6)G code can be sent on the screen (7)The color of RGB can be adjusted according to preferences (8)Support downloading models via TF card and U disk 5. Steel: BIQU SuperSpringSteel 6. Interface: BLtouch Smart Filament Sensor interface BLtouch bracket Integrated adapter board Type-C 7. Nozzle: The nozzle shell is detachable (easy to replace parts) RGB can be DIY More about B1: 🤍 FB Homepage: 🤍 FB Group: 🤍 🤍 Twitter: 🤍 AliExpress: 🤍 Banggood: 🤍 If you want to become a distributor or order in large quantities, please contact our sales: luciano🤍biqu3d.com!

Do I regret Buying The Biqu H2 V2S Lite Direct Drive Extruder? - My Experience

2914
32
56
00:21:23
22.10.2022

My experience installing and using the Biqu H2 V2S Lite was horrible, especially in the beginning. The customer service as slow and seemed like the language barrier really got in the way of any real progress. Having now recovered from the nightmare that was installing it, would I now recommend the V2S Lite to people? A contingent yes. Let me know what you thought of the video in the comments! :) - Where Can You Buy My Gear? - Biqu H2 V2S Lite: 🤍 Reliable BL Touch: 🤍 Volcano Heat Blocks: 🤍 Volcano Nozzles: 🤍 Biqu Throat Tubes: 🤍 Best Thermistors: 🤍 Thermal Paste (For Throat Tube): 🤍 The BEST Printer Grease: 🤍 Neptune 3 Printer: 🤍 Neptune 2S Printer: 🤍 BEST personal resin printer: 🤍 My FAVORITE filament brands: 🤍 + 🤍 Silicone Covers: 🤍 Easy Loom Tubing: 🤍 The BEST Leveling Buffers: 🤍 50mm 5015 24V Fans: 🤍 Dual Z Axis Kits: 🤍 Reliable Filament Dryers: 🤍 xTool D1 Pro 20W w/ Rotary Kit for the ULTIMATE engraving and laser experience: 🤍 Camera Equipment: Sony A7IV Full Frame Body: 🤍 Sigma 14-24mm 2.8 DG DN Art Lens for wide shooting: 🤍 Sony 85mm 1.4 GM lens for high detail work: 🤍 Video Cage for Sony Body: 🤍 Neewer 660 PRO RGB Lights: 🤍 My Ergonomic Desk Chair: 🤍 Time Stamps: 0:00 - Video Start 2:48 - Con 1 (Nozzle Availability) 3:52 - Con 2 (Bad/Slow Support) 6:08 - Con 3 (Mounts, Shrouds, Firmware Building Issues) 7:25 - Fan Shroud Design Issues 9:47 - I Buy Another (Bad Experience) 12:26 - More Bad Customer Service 14:00 - I Find My Own Solution 14:58 - Pros and Cons Overview 15:53 - Print Examples 18:12 - Would I Recommend It? 20:36 - What's To Come!

Biqu Bx 3D Drucker auspacken und erster Druck -Genial-

2697
53
15
00:37:01
20.05.2021

In diesem Video stelle ich euch den brandneuen 3D-Drucker Biqu BX vor. FDM Drucker Direkt Extruder leise TMC 2226 Treiber Motherboard 32 bit und 400 mhz Magnetfolie mit abnehmbarer Dauerdruckplatte Doppel Z-Antrieb Meanwell Netzteil 7-Zoll Touch Display

How to fix BIQU H2 gear clicking

4450
120
29
00:09:20
23.06.2022

My BIQU H2 direct drive extruder was plagued with the clicking gears that several complain about, although I didn't have any print quality issues so I left it alone except for slowing down my printer to minimize the sound. Well today while cleaning out some filament debris I found what I believe is the problem. Basically the holes that hold the bearings are a tiny bit too large so they are able to wobble in place. This video will show you how to fix that with a virtually free solution using Kapton tape. Hopefully this fix works for you. let me know in the comments how it went.I enjoy reading the feedback. thanks for watching

Imprimante 3D BIQU-B1: Montage et premiers essais

212
4
2
00:06:07
06.09.2022

Je vous présente une vidéo montrant les étapes de montage, de réglages, des premiers essais d'impression et mes premières appréciations de l'imprimante BIQU B1. Un immense merci à Renaud ILTIS de CNCFAB (🤍 pour l'imprimante et ces précieux conseils. Retrouvez son programme de formation sur son site Tamtam3D,, 🤍 Vous pouvez me suivre sur mon site eol37.aeromodeler.com ou sur ma page Facebook 🤍

BIQU B1 || Best Budget 3D Printer! (Much Better than Ender3)

5703
112
29
00:25:03
19.02.2022

In this video I did the unboxing, installation and review of the Bigtreetech biqu b1 3d printer Bigtreetech has many products related to 3D printers. This one is Biqu B1 FDM 3D Printer 32 Bit Dual Operation System(marlin and touchscreen mode) and i must say that Biqu b1 is much better than Creality Ender 3/3 v2. Biqu b1 has tft35 touch screen, btt SKR V1.4 mainboard, magnetic sheet heated aluminum bed, and much more. Buy link - 🤍 Official website - 🤍 Contents time: 00:00 - Unbox 05:15 - Set up 13:40 - First run 19:58 - Printing

BIQU B1 FDM 3D Printer for Beginners and Experts | SainSmart

2270
8
0
00:02:23
16.06.2021

With a 4.3-inch color touchscreen and dual user interface, the B1 offers some beginner-friendly features for easy calibration and setup, as well as countless features for advanced users to get the most out of their printer!

Ender 3 V2 vs BIQU B1 - Battle of the upgraded Ender 3s

172479
3488
342
00:14:13
17.07.2020

Creality has released the Ender 3 V2, similar to the Ender 3 but with sleeker looks and some upgraded parts. BIQU has also released the B1, an Ender 3 clone with many of the Bigtreetech parts that people fit as upgrades to the Ender 3. In this video, I look at the specifications, unbox, assembled and test prints to see which one holds more promise. Both are off to a good start, and I’ll have a full head to head review to follow. If you want me to test something, leave a comment. Both machines were provided free of charge for the purpose of review. All opinions expressed are my own. Purchase the Ender 3 V2: 🤍 Purchase the BIQI B1: 🤍 Form Futura Silk gloss PLA from X3D: 🤍 Models in this video: 3D Benchy: 🤍 Vase: 🤍 Collapsible basket: 🤍 Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: 🤍x3d.com.au Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5] 🤍 Take a look around and if you like what you see, please subscribe. Support me on Patreon: 🤍

BIQU H2 V2 Compact Direct Drive Extruder fan duct 5015

456
8
5
00:05:00
24.12.2022

3D Design fan duct for 5015 fan secound version optimized with Computational Fluid Dynamics (CFD) Download STL from: 🤍 Print settings: 1.2mm wall thickness No support structure for the fan duct part use heat resident filament over 150° my recommendation: Green-​TEC PRO made by Extrudr

BIQU H2 V2 Compact Direct Drive Extruder fun duct 40x20

1112
17
2
00:03:09
09.10.2022

Download STL Dateien: 🤍 fun duct 40x20

BigTreeTech BIQU H2 500c Install with Dual Parts Cooling Ducts on Corception 300 / Creativity ELF

2985
50
28
00:59:06
30.06.2022

Designing a custom linear rail mount in OnShape for installing the BIQU H2 High Temp Extruder to a CoreXY 3D printer. 🤍 BIQU H2 500c Kit - 🤍ent/collections/h2-series-extruder/products/h2-500-extruder-for-3d-printer Creativity ELF - 🤍 New to the channel? Consider subscribing, liking, commenting, and sharing this video. More DIY coming soon. Thank you for watching! - Music: Olive Spring by Imperss is licensed under a Creative Commons License. 🤍 Support by RFM - NCM: 🤍 - Music: SWAY by tubebackr is licensed under a Creative Commons License. 🤍 🤍 | 🤍 Support by RFM - NCM: 🤍 -

Tronxy Crux Biqu H2 install

1113
28
3
00:07:37
27.10.2022

Biqu H2 Fan Mount 🤍 Trimed Version 🤍 Extruder mount for the Crux 🤍 Fan Adapter 🤍 Support me on Patreon 🤍 Tronxy Store Link: 🤍 Save 2% Coupon code: JEFFS3D Click on a link to help the channel! Affiliate Links U.S Amazon: BIQU H2 Extruder V2.0 🤍 Ender V2 Pro links: 🤍 Ferrule Crimping Tool 🤍 BIGTREETECH SKR 2 (with 5pcs TMC2209) 🤍 Tronxy Black TR Auto Leveling Sensor + Lattice Glass Plate 255×255mm 🤍 linear rail choose 350mm :🤍 Buck Converter: 🤍 Wire Stripper: 🤍 Pi camera link 🤍 HICTOP Ender 3 Dual Z-axis Upgrade Kit 🤍 3DTouch 🤍 Jump Wires 🤍 Kingroon KP3S 🤍 Voxelab Aquila 🤍 Affiliate Links Canada Amazon: BIQU H2 Extruder V2.0 🤍 Ender v2 Pro 🤍 Ferrule Crimping Tool 🤍 BIGTREETECH SKR 2 (with 5pcs TMC2209) 🤍 Tronxy Black TR Auto Leveling Sensor + Lattice Glass Plate 255×255mm 🤍 linear rail choose 350mm :🤍 Buck Converter: 🤍 Wire Stripper: 🤍 Pi camera link: 🤍 HICTOP Ender 3 Dual Z-axis Upgrade Kit : 🤍 Creality upgrade kit: 🤍 3DTouch 🤍 Jump Wires: 🤍 AnyCubic Chiron 🤍 Tronxy XY2 Pro 🤍 Kingroon KP3S 🤍 Voxelab Aquila 🤍 My Dropbox: 🤍 Follow me on Instagram Jeff's 3d Corner 🤍 Want to send me something to test? Have a Idea for a video? Reach out and let me know. Royalty free music by: 🤍 Intro music created by Noah Wilson.

BL touch biqu 1

1808
20
8
00:00:57
13.03.2021

Is a $299 3D Printer any good?? BIQU B1 Review

16962
859
45
00:17:13
02.02.2021

If you want to support my channel, please consider using one of my affiliate links below to give me a small kickback at no cost to you :) AliExpress: 🤍 Amazon: 🤍 BIQU B1 Official website:🤍 -Schematix- 0:00 Intro 0:43 Assembly 5:52 Bed Leveling 6:32 Slicer Software 7:25 Printing 9:46 Print Results 12:44 Pros & Cons 15:22 Conclusion

La BIQU Hurakan : Klipper + Plein de petits trucs spéciaux

5940
339
37
00:40:26
10.12.2022

La BIQU Hurakan : Lien vers l'imprimante : 🤍ent/products/biqu-hurakan-diy-3d-printer Pour supporter la chaine du GueroLoco : Devenir ami du GueroLoco en rejoignant la chaîne : 🤍 Don Paypal : 🤍

BiQu B1 SE Plus Full Assembly video

3578
62
15
00:35:28
17.01.2022

BiQu B1 SE Plus Full Assembly video Here we have the full assembly video step by step for BiQu B1 SE plus. I tried to do close shots and detailed everything you need to know. I hope this video helps a lot to you guys during your journey! Here are the quick jumps for this video: Introduction: 00:00 Gantry and base: 01:00 Extruder: 08:00 Heated bed: 16:20 Filament holder: 17:34 First start: 20:00 My bug: 20:25 Fixing the bug: 21:24 Again first start: 23:20 Screen operation: 23:30 Heating up: 28:50 Auto bed leveling: 30:35 First print started: 32:13 Ending: 34:20 Here is a quick link to this 3D printer: 🤍ent/products/biqu-b1-se-plus-3d-printer BQ on facebook: 🤍 I will be making many videos about it. Here are the links: (I will add as they come) 1) unboxing video: 🤍 2) assembly video: 🤍 3) cura settings: coming soon 4) review: coming soon About this printer: Print volume: 310x310x340 mm Nozzle size: 0.4 mm Print accuracy: +- 0.05 mm Filament: pla, petg, tpu, tpe, abs, nylon Output voltage: 24V Max bed temp: 100C Max nozzle temp: 260C 3D Printing Doctor Social Media Instagram (20K) : 🤍 Tiktok (6K) : 🤍 Reddit: 🤍 All my links summarized: 🤍 You know my YouTube haha! #Biqu #biquB1SEPlus #3DPrinter biqu b1 se plus assembly steps

Everything you need to know about BIQU H2O

9063
176
69
00:24:05
02.05.2022

🆓📈💵 How to water-cool your 3D printer with the BIQU H2O kit and what are the benefits of adding this tech to your printers are. A complete guide for hardware installation and marlin changes for SKR Mini E3 and other boards. 🔗 Extra info: 🤍 🛒 BIQU H20 Extruder: 🤍 🛒 Tubing: 🤍 🛒 SKR Mini E3 v3.0: 🤍 🛒 5020 fans: 🤍 🛒 4020 fans: 🤍 🛒 Coolant: 🤍 🛒 JST Connector kit: 🤍 More about silent 3D printing: 🤍 = Table of Contents: = 0:00 - Intro 02:00 - Why would you water-cool your 3D printer 04:48 - Reasons not to get BIQU H2O 06:48 - How to install BIQU H2O 14:00 - Configure BIQU H20 in Marlin 19:49 - Water-cooling 3D printer - conclusions = Social Media & Business Contact: = 2nd YT channel:🤍 Twitter: 🤍 Facebook: 🤍 Instagram: 🤍 Reddit: 🤍 Business Contact: 🤍 = Patreon & PayPal: = If you wish to support the channel monetarily, check the options here: 🤍 Created thanks to the support of the Patrons: oolara, Alan C A, Arya, Dane M, Daniel, G, David G, David M, DoomedSardines, Herik A, Jack C, Kim B, Leroxy, Natasha W, Nis L, Noodle, Sandra I, Tony L With extra support in May from: Andre S, Francisco H, = Gear Used to Make This Video: = Camera: 🤍 Secondary Camera: 🤍 Microphone: 🤍 Secondary Mic: 🤍 B-Roll kit: Slider, Pan & Tilt: 🤍 DSLR Gimbal: 🤍 Action, Vlog Kit: Phone: 🤍 360 Camera: 🤍 Action Camera: 🤍 Mobile Gimbal: 🤍 Drone: 🤍 Sound Recorder: 🤍 Streaming Kit: Webcam: 🤍 Microphone: 🤍 HDMI capture card: 🤍 = Music: = Hip Jazz by Benjamin Tissot - 🤍bensound.com Product affiliation, sponsorships and affiliate links More information: 🤍 Transparency Legend: 💳 – I paid for the item with my own money 🆓 – I was interested in the item, received free of charge 📈 – I used links that bring me affiliate payments 💵 – content commissioned, I retain 100% creative and critical control 💰 – ad/ sponsored content possibly vetted by the sponsor = #3Dprinter #BIQU #H2O

BIQU B1 with GH Input Shaping Motor Drivers

4368
41
23
00:14:52
28.07.2022

GH Smart Shapers Boards 🤍 Available on Amazon 🤍 The introduction of Input Shaping techniques has made it possible to print at unprecedented accelerations. Due to the shortage of electronic components (raspberry boards are practically unavailable) and to the required skills, Klipper is not yet a solution within everyone's reach. GH Enterprise has therefore found a solution that allows you to add Input Shaping to 3D printers in a simple and immediate way, without using Klipper and without external host cards such as RPI4. Just replace the X and Y axis drivers with the GH Smart Shaper drivers, add some configuration commands to your g-code and you are ready to print with input shaping. X acceleration 25000 mm/s2 Y acceleration 18000 mm/s2 InputShaping MZV X= 47Hz Y= 51Hz Printing Speed 200 mm/s #SpeedBoatRace #JoinTheSpeed

Installation tutorial for #BLTouch on #BIQU B1

30403
219
44
00:03:14
09.07.2020

It’s known that in order to facilitate the installation of BLTouch, our B1 reserves the BLTouch interface and a free BLtouch holder for buyers. This video is designed to help you successfully install BLTouch on B1. More about B1 can be seen on: 🤍 FB Homepage: 🤍 FB Group: 🤍 🤍 Twitter: 🤍

Artillery x2 modification avec lit alu et extrudeur biqu h2 x2

397
10
2
00:00:24
26.11.2022

Pour plus d'information allez voir mon sujet sur le forum 🤍

Ender 3 v2 BIQU H2 Direct Drive Upgrade

40175
610
77
00:06:21
10.06.2021

🛒 Get the BIQU H2 Extruder here: 🤍 🛒 Get BIQU Filament here: 🤍 In this video, I'll tell you my opinions on the BIQU H2 extruder, which I have mounted to my Ender 3 v2. 3D PRINTED PARTS (Preferrably print these in PETG!) Remixed MIQU H2 mount, BLTouch and fan shroud 🤍 Biqu H2 Mount + Cover - Ender 3 CR10 🤍 BIQU H2 Ender 5 Mount and Fan Shroud 🤍 Biqu H2 Upgraded Mounts for Ender 3 v1 & v2 🤍 SAMPLE PRINTS Voron Testcube 🤍 3D Benchy 🤍 Vase Mode Dot Jars by Clockspring 🤍 Flexible Octopus 🤍 Rectangular trash can ( Vase Mode ) 🤍 THE PRINTERS I USE: 🤍 MY MERCH: 🤍 BECOME A PATRON: 🤍 CHAT ON DISCORD: 🤍 BUSINESS INQUIRIES ONLY (OR IF YOU WANT TO SEND SOMETHING) - DANIEL🤍CROSSLINK.IO FOLLOW ME: INSTAGRAM - 🤍 TWITTER - 🤍 FACEBOOK - 🤍 WEBSITE: 🤍 The Music I use: 🤍 AMAZING for YouTubers! GEAR USED 🤍 Disclaimer: As an Amazon Associate I earn from qualifying purchases.

BIQU Hermit Crab Quick-change Tool Changer

34657
124
14
00:01:24
20.09.2021

BIQU Hermit Crab Upgrade, launched by Shenzhen Big Tree Technology Co., Ltd, is a quick-change tool changer for most existing 3d printers. It is compatible with V-slot rollers when using the adapter plate or with MGN12H rails when using the standard base plate. Features: ⇨Upgrade of traditional POM slider / Smoother moving. ⇨Compatible with various hot ends, such as nozzles, laser heads, and CNC cutter heads ⇨High motion precision and excellent printing performance. ⇨With spring clips, easy to install and remove ⇨High adaptability, with multiple ports and fixed holes. ✔【Last & Durable】Hermit crab is a workhorse, which is made of Aluminum alloy 6061 and able to resist long periods, and made to ensure consistency. ✔【Upgrade of Traditional POM slider】Smoother moving,High motion precision, Excellent printing performance. ✔【Easy to Install and Remove】With spring clips, easy to install and remove. The Hermit Crab makes it so simple to swap out any hot end or tool. ✔【High Compatibility】High compatibility, with multiple ports and fixing holes. It is able to mount various hot ends, such as nozzles, laser heads, and CNC cutter heads. Two versions: Standard board and CAN version. The CAN version has fewer wiring harnesses, but there are more cool adapter boards, and it can only be used to run Klipper firmware on the Raspberry Pi. Officially available on Aliexpress, eBay and Shopify already. ☺ AliExpress: 🤍 ☺ eBay: 🤍 ☺ Shopify: 🤍 Official website: 🤍 BIQU (FB homepage): 🤍 BIGTREETECH (FB homepage): 🤍 BIQU (Twitter): 🤍 BIGTREETECH (Twitter): 🤍

📌H2 V2S Revo: BIQU X E3D frustration-free extruder for 3D Printers.

3685
35
10
00:00:56
27.08.2022

H2 V2S Revo combines the strengths of H2 and E3D Rapidchange Revo. It retains the lightweight and offers convenience to change nozzles——🤍E3D Revo Nozzles. Besides, Revo HeaterCore speeds up the heating time and provide the protecting mechanism. Detailed Features: 🎯Light Weight: 198g. 🎯Maximum Printing Temperature: 300°C. 🎯E3D Revo #Nozzle: quicker and easier to change just using your hand. No tools and no hot-tightening needed. 🎯E3D Revo #HeaterCore: faster and safer heat-up times than other HotEnds. 🎯E3D Revo #HeaterCore -PTC: heating power reduces as it gets hotter. Intrinsic hardware protection against thermal runaway. 🛒Offcial: 🤍 🛒Aliexpress: 🤍 ⭐Follow⭐ [Official] BIQU: 🤍 [Facebook] BIQU:🤍 BIGTREETECH:🤍 [Twitter] BIQU:🤍 BIGTREETECH:🤍 [Instagram] BIQU: 🤍 BIGTREETECH:🤍

Назад
Что ищут прямо сейчас на
Biqu windows ME kik fuxeris UP X С 1 РУБЛЯ DUBLADO ласт UPRO hyein of newjeans cronus zen 2k23 blender shapes Ark Mods курсы css винди31 lily collins emily in paris memu player lag fix in sinhala как разделить текст Lazarus beniju koreshzy